Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 136 of 175
The impeller material in the fuel pump is unsuitable, causing the impeller to swell and deform due to fuel components, potentially interfering with the impeller case. Continued operation may result in impeller …
Improper solder joints on internal terminals of the injection relay controlling fuel supply and the main relay controlling power supply may cause relay malfunction. Continued use in this condition could result in …
Due to improper electrical circuitry in the lighting system, the brake light does not illuminate when the auxiliary braking device (electromagnetic retarder) is activated. Additionally, this defect can damage the brake light …
Insufficient strength in the knuckle stopper area of the front axle can result in excessive stress on the kingpin boss during vehicle cornering and similar operations, potentially causing cracks in the stopper …
The cooling water hose of the fluid-type auxiliary braking device mounted on the transmission has insufficient durability. Cracks develop due to vibration during operation, and in some cases the hose becomes detached. …
The air charge pipe, which supplies compressed air to the brake system air tank, has insufficient strength. Cracks may develop in this pipe due to vehicle body vibration and similar factors. If …
Some airbag control units were mistakenly equipped with a passenger vehicle G-sensor (high sensitivity type). Continued use in this condition may cause the airbag to inadvertently deploy due to strong road surface …
The vent ring (with a vent valve to prevent liquid fuel from being drawn into the fuel vapor canister during operation) welded to the resin fuel tank has improper molding. Repeated expansion …
Injuries — Risk of injury. The front suspension lower ball joint may wear and become loose; in extreme case ball joint may separate from knuckle and cause loss of steering control.
The attachment clip securing the connection between the brake pedal and pushrod may not be properly installed on some vehicles. Repeated brake operation could cause the connection to separate, potentially resulting in …
On vehicles equipped with a rear body, the stopper rear body mounting position is improper, resulting in insufficient clearance between the stopper rear body mounting bolt and the rear brake pipe on …
On vehicles equipped with a rear body, the rear brake pipe clamp was not installed, causing the brake pipe to vibrate and potentially interfere with the stopper rear body mounting bolt. Continued …
The mounting bolts securing the air tank and battery box bracket are improperly tightened. These bolts may detach due to vibration during operation. If left unaddressed, the air tank may tilt, damaging …
The fuel return pipe attachment point on the fuel pump has improper molding, which may cause cracks at the attachment point due to vehicle vibration and other factors. Continued use without remediation …
The support position of the hydraulic power steering piping (feed hose) is improper, causing the hose to be excessively bent and subjected to excessive forces, which may result in cracks. This can …
In the brake master cylinder, some vehicles have brake pipes assembled in incorrect order, resulting in insufficient clearance with the power steering pipe. During vehicle operation, vibration may cause the brake pipe …
The rear brake pipes of the anti-lock brake system (ABS) may be installed with left and right sides reversed. As a result, when braking that activates ABS occurs, braking force is applied …
The air compressor outlet air temperature is high, causing compressor lubricant to carbonize and accumulate inside the air outlet pipe. If operation continues in this condition, deposits inside the pipe are heated, …
Improper routing of brake air piping causes interference with the driver-side step mounting bracket. Under normal use, vibration during driving may damage the piping, potentially resulting in air leakage causing horn failure, …
The cruise control cancel switch attached to the master cylinder has an inadequate internal seal structure, allowing brake fluid to leak onto internal electrical terminals and causing corrosion. This increases internal resistance, …
The lighting control module (LCM) has an inadequate breaker function. When electrical load exceeds capacity—such as when additional lighting is installed—excessive current flows through the LCM, causing overheating. This can result in …
Fire — Risk of fire. A fuel line jumper tube may chafe against the throttle cable; chafing of the fuel line may result in a fuel leak over time and can cause …
The torque rod mounting bracket of the front axle suspension device has insufficient strength. Repeated braking loads on the bracket can cause cracks in the mounting components. If use continues without remedy, …
In the ball joints of the upper and lower arms in the independent front suspension system, the dust boot seal structure is inadequate. This allows mud and water to enter the joint, …
On large buses equipped with mixer-type CNG engines, improper routing of the accelerator cable results in insufficient clearance between the oil pressure hose or power steering hose and the cable. Continued use …
①On large buses equipped with gas valve-type CNG engines, the accelerator cable routing is improper, resulting in insufficient clearance between the fuel hose or power steering hose and the cable. Continued operation …
Improper assembly of the coupling between the steering shaft and gearbox results in shallow engagement between the coupling and gearbox in some units. Repeated steering operations cause wear and play at the …
The fastening structure of the rubber-equipped bracket securing the fuel injection pump's injection tube is inadequate. As the bracket's rubber deteriorates, the mounting bolts and nuts loosen, potentially causing the bracket and …
The end shape of the rubber seal at the rear of the brake master cylinder is inappropriate, causing part of the seal to curl up during brake operations after brake fluid filling …
The tie rod spring that prevents detachment in the tie rod controlling engine fuel injection quantity has insufficient strength. Repeated engine shutdowns can cause this spring to fracture. If use continues in …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.