Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 142 of 175
On vehicles equipped with spring-applied parking brakes, improper heat treatment of the roller at the wedge tip that expands the brake shoe, or improper assembly of wedge component parts, may cause wedge …
In vehicles equipped with spring-type parking brakes, improper internal dimensions of the spring storage chamber and inappropriate spring seat geometry can cause spring-to-spring or spring-to-chamber interference during spring compression (parking brake release). …
The parking brake cable end fitting on the center brake side is improperly shaped, causing the cable end to sit at an angle in the lever groove. This can result in bending …
The rear axle upper torque rod bracket attachment to the frame lacks sufficient strength. High stress develops during rapid acceleration or braking, causing cracks. Continued use may result in bracket fracture, which …
During the fuel hose inspection process at the manufacturing facility, improper force was applied to the resin pipe section of the fuel pump during inspection, causing microscopic cracks to develop in some …
The ground cable for the alternator has an inadequate wire gauge. During power generation, the cable's allowable current rating is exceeded, causing the cable to melt and burn. In worst cases, this …
Some brake light switches have been sprayed with inappropriate lubricant during the vehicle manufacturing process. As a result, lubricant components may oxidize during use, increasing contact resistance at the switch contacts and …
The wheel hub-side joint portion of the rear axle shaft has an improper geometry, causing operational loads to concentrate at the joint root. This can result in crack initiation at the root. …
The hub nuts on the front and rear wheels have improper fastening torque settings, which may cause them to loosen during operation. If driving continues in this condition, the hub nuts may …
The brake shoe heat treatment in the braking system is inadequate, resulting in insufficient adhesion between the brake shoe and lining in some units. Repeated brake operation may cause the lining to …
The fastening structure of the rubber-fitted bracket securing the injection tube of the fuel injection pump is inadequate. As the rubber deteriorates, the fastening bolts and nuts become loose, and the bracket …
In vehicles equipped with ABS (Anti-lock Braking System) and hill-start assist device (EZGO: Easy Go), improper machining within the hydraulic control unit may cause brake pedal travel to increase during braking after …
The hose length of the rollover shutoff valve (front) installed to connect the left and right fuel tanks to the canister is inappropriate. Continued use may cause the hose to fracture due …
In training vehicles equipped with diesel engines and manual transmissions, the front exhaust pipe structure is inadequate, causing high stress to develop in the pipe bellows section due to engine vibration during …
Improper fastening of cabin electrical wiring causes assembly process variation, resulting in insufficient clearance between some hood lock release handle brackets and the wiring. The bracket mounting bolts can damage the wire …
The parking brake solenoid valve has inadequate water-resistance design, allowing water ingress into the internal structure. Corrosion of the solenoid coil can cause coil short-circuit and loss of function. In the worst …
The protective covering and fixing method of the electrical wiring for the parking brake solenoid valve is inadequate. Vibration during operation may cause the electrical wiring to interfere with the filter mounting …
The air piping (nylon tubing) for the parking brake (wheel parking brake) has insufficient routing clearance. Rear axle vertical movement during driving and height control operation causes the nylon tubing to interfere …
The lock system of the gull-wing doors on the rear of the vehicle body has inappropriate spring return force settings for the lock that engages with the catch, and improper reaction force …
The ball stud strength of the knuckle arm is insufficient. Repeated heavy steering lock usage or high-frequency steering operation can cause cracks to develop in the ball stud. If use continues in …
The rack controlling fuel injection quantity in the fuel injection pump has insufficient strength in its notch groove, and the fuel injection pump mounting method to the engine is inappropriate. Continued use …
During axle assembly, some vehicles have improper lock nut torque on the front wheel hub outer bearing or insufficient grease fill between the front wheel hub outer bearing and hub body. Consequently, …
During axle assembly, some units have improperly tightened lock nuts on the front wheel hub outer bearing and insufficient grease fill in the front wheel hub body. This can cause the bearing …
On vehicles equipped with four-bellow air spring suspension, the ball joint at the center of the V-rod that fixes the rear axle to the frame may have insufficiently tightened nuts. Continued operation …
The oil hose in the automatic transmission fluid cooling circuit has insufficient heat resistance. When transmission fluid temperature rises excessively, such as during hill climbing, the hose may degrade and rupture, causing …
The muffler lacks sufficient rigidity against exhaust pressure, and internal welding is inadequate. Continued use in this condition may cause weld fractures, resulting in exhaust gas leakage. Exhaust heat can melt surrounding …
In large-capacity route buses, the starter system has inadequate hardness of the flywheel ring gear and improper wiring length in the starter magnetic switch activation circuit. During starting operation, the starter pinion …
In turbocharged manual transmission vehicles, the fastening bolt of the Oil Control Valve (OCV) cover, which hydraulically controls engine intake valve timing, has insufficient clamp load. During continuous high-load, high-RPM operation, internal …
Due to improper software in the airbag control unit, the front seat occupancy sensor may fail to detect passenger presence. In the event of a collision or accident, the front passenger airbag …
Due to improper software in the airbag control unit, the front seat occupancy sensor may fail to detect passenger seating. In the event of collision or accident, the passenger airbag may not …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.