Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5188 matching recalls · page 151 of 173
In the braking system, some vehicles have improper routing of the left front brake pipe, which can cause the pipe to interfere with the anti-roll bar link when the steering wheel is …
In the lighting system, the contact resistance capacity setting of the relay in the brake light electrical circuit is inappropriate. Repeated brake operations cause the contact surface to become rough, resulting in …
In vehicles equipped with front fog lamps, some fog lamp bulb sockets are improperly assembled. Vibration during driving may cause the bulb socket to detach from the fog lamp housing. Heat from …
In the braking system, the brake hose is improperly secured to the front strut area. During vehicle operation, vibrations may cause the brake hose to become dislodged from the retaining bracket. If …
In the power transmission device, the lock nuts fastening the bearings of the bevel pinions in the front differential have improper fastening torque and staking. Continued use in this condition may allow …
The brake system ABS control unit (ABS/ECU) connector interface with the vehicle wiring harness has incomplete waterproofing. Water intrusion at this joint can cause electrical short circuits, illuminating the ABS warning light …
In the braking system, some brake fluid has inappropriate viscosity. At low temperatures, brake fluid flow becomes sluggish, causing delayed brake engagement and release response when the brake pedal is operated, which …
The support bracket that secures the steering column shaft to the vehicle body has insufficient strength. Repeated abrupt steering wheel operations can cause cracks in the support bracket, resulting in unstable steering …
In the electrical system, improper routing of battery wiring within the right side frame may cause the wiring to interfere with the clip securing the brake control nylon tube due to vibration …
The intermediate arm shaft in the steering device linkage has insufficient strength, causing bending in some units. Continued use in this condition may result in bearing failure and, in the worst case, …
In the braking system, the rivet fastening method at the pivot point of the parking brake lever is improper. When the parking brake is operated, this area may twist, causing insufficient ratchet …
In the steering system, some vehicles have insufficient fastening torque on the bolt and nut that secure the right-side knuckle to the front strut. This can cause the bolt and nut to …
In the electrical system, V8 engine equipped vehicles have relay terminals for the low-pressure fuel pump drive circuit in the relay box made of inappropriate material. Engine compartment temperature rise and heat …
The adhesive securing the vibration-damping rubber on the crankshaft pulley that drives the accessory belt has insufficient heat resistance. At elevated temperatures during high-speed driving, adhesive bond strength deteriorates, causing the pulley …
In vehicles with automatic transmissions, the brake light switch electrical wiring circuit is improperly configured, causing the switch contacts to overheat and the resin component to melt. In the worst case, the …
In the steering system, some yokes connecting the steering column and gearbox have cracks due to improper heat treatment. Continued use in this condition may result in yoke failure, rendering the steering …
In the steering system, the steering shaft coupling joint is assembled in an improper position, resulting in the coupling not being fixed in the correct position. Continued use in this condition may …
In the powertrain system, the spring retaining position on the rod that locks the parking mechanism gear of the automatic transmission is inappropriate. Even when shifting to park position, the parking mechanism …
In the air heater that raises the temperature of intake air to the engine and improves cold-start performance, either ① insufficient waterproof and corrosion-resistant performance of the air heater relay, or ② …
Driver-side airbag inflator housings may have improper welds. During airbag deployment, partial housing fracture can occur, resulting in insufficient inflation gas supply and incomplete airbag deployment during collision. Additionally, fragments of the …
Due to improper machining of internal terminals in the vehicle speed sensor embedded within the left front wheel hub, vibration during operation may cause contact failure at the terminal section, preventing speed …
The intermediate arm shaft in the steering device linkage has inadequate strength, causing bending in some cases. Continued use in this condition may result in bearing damage and, in the worst case, …
In the braking system, the structure of the front-wheel brake hose and the positional relationship between the bracket securing the brake hose and the wheel cylinder are improper. When the brake hose …
The axle spindle in the running gear has insufficient strength. Continued use in this condition may cause cracks to develop in the spindle, and in the worst case, fracture and wheel detachment.
In hybrid system-equipped vehicles, charging control for the motor-drive battery is partially inadequate, which may cause temporary insufficiency of intake manifold vacuum acting on the vacuum-operated brake booster immediately after cold engine …
In the brake system, the gap between the brake pipe and leaf spring is improper, causing the brake pipe to contact the leaf spring and sustain surface damage. The surface plating peels …
In the front suspension system, some vehicles have insufficient bolt torque securing the strut to the knuckle. If operation continues in this condition, the strut may disengage from the knuckle when traversing …
The plastic nut securing the fuel pump unit to the fuel tank may be improperly tightened, with some units installed at an angle. If the vehicle continues to be used in this …
In the steering system, the steering arm mounting bolts and washers are made of inappropriate material. Repeated steering operations cause these bolts and washers to gradually deform, resulting in insufficient clamping force …
In the fuel system, certain fuel pumps have improper clearance between the internal rotating valve and the inner wall of the rotating valve chamber. Due to temperature fluctuations, the rotating valve and …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.