Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
10646 recalls on record · page 294 of 355
Electrical wiring between the frame and body in the vehicle front section has insufficient durability of wire insulation against vertical vehicle motion during low temperatures. Vibration during driving may cause cracks in …
In manual cab-tilt mechanisms of medium-duty trucks, inadequate clearance between the cab hook and surrounding components causes the cab hook to interfere with adjacent parts when the cab is lowered, resulting in …
The engine control unit program is inadequate, causing excessive amplitude of the throttle valve at its closed position, which may damage the electronic throttle motor stopper. This causes engine control to enter …
The rear spoiler mounting bolts and washers at the vehicle rear are improperly secured, causing the bolts to loosen due to vibration during driving, resulting in spoiler rattling noise. If driving continues …
①The program in the built-in system interface that controls the power supply of the vehicle's electrical system is inappropriate, which may cause the horn to activate and not stop when the door …
The fixing position of the hydraulic hose around the control cable for forward/reverse operation lever is improper on some units, causing the cable to interfere with the hydraulic hose during left/right turns. …
The locking structure of the bearing nut on the oscillation center pin and its fastening torque specification are inadequate. During vehicle operation, when oscillation occurs, the bearing washer for nut locking moves …
The contact durability of the intermittent operation relay built into the wiper actuator is insufficient. Repeated use in intermittent mode causes contact wear and partial detachment. Detached contact particles can lodge between …
Certain tailgate lifters have insufficient arm strength connecting the gate lift/lower hydraulic cylinder to the gate lift/lower link, and improper pressure relief valve settings on the cylinder. Repeated gate operation can cause …
The PCV hose routing directed to the intake manifold has an inadequate shape, causing the hose to expand and contract due to engine intake pressure fluctuations. Continued use may allow fine cracks …
Improper routing of the vacuum hose for the pressure regulator (fuel pressure control device) allows water droplets generated in the intake manifold during operation to enter the pressure regulator through the vacuum …
The mud-water intrusion prevention plate (dust cover) attached to the rear of the rear axle (non-drive axle) brake drum on two-rear-axle trucks has an inappropriate shape. During rainy conditions, mud and water …
The axle shaft has insufficient strength and may develop cracks due to prolonged use. Continued operation in this condition could result in axle shaft fracture, leading to loss of vehicle mobility.
The surface treatment of the front camshaft gear fixing bolt is inadequate, which may cause the bolt to loosen. Continued use in this condition may result in the camshaft gear loosening, and …
④In the seating apparatus, the mold of the bracket that secures the seat to the cabin is insufficient, causing the mold to peel off in some cases. As a result, the seat …
③ Insufficient durability of the knuckle arm pin causes wear in some units. Continued use may result in steering wheel play, potentially compromising driving stability.
Some bolts securing the steering linkage pin lack sufficient tightening force, which may cause the bolt to loosen. If use continues in this condition, the bolt may fall out, and in the …
① Improper welding of the kingpin that supports the two-wheel/four-wheel steering mode-selector device at two upper and lower locations may cause cracks to develop at the weld joint between the pin and …
The power steering pump contains a spool valve that regulates internal pressure to prevent it from exceeding specified values. Due to tight clearances in this valve, if foreign matter (sand) contaminates the …
Due to improper programming in the engine control computer, when fuel evaporative emissions are supplied, the air-fuel ratio becomes lean, causing exhaust temperature to rise. As a result, the front catalytic converter …
Front hub strength is insufficient. Repeated high-frequency cornering and other driving conditions may cause cracks to develop near the base of the hub flange. Additional factors such as maintenance condition and load …
Certain crossmember components at the vehicle frame attachment points of the torque rods that secure the rear axle have inadequate corrosion protection. Continued use in this condition allows rust to initiate and …
In vehicles modified into X-ray trucks, insufficient frame strength causes cracks to develop on the mounting surface of the lateral rod bracket on the right-side frame. Continued use in this condition may …
The connector shape of the fuel hose connected to the fuel tank is inappropriate, which may cause incorrect installation of the connector to fail during operation. Continued use in this condition may …
The shift control cable that transmits select lever operation to the automatic transmission has an incorrect cap component installed for securing the cable to the vehicle. This may cause the cable to …
The air box drain tube routing is improper, causing interference with the front cylinder exhaust pipe, which may melt and rupture. In the worst case, this could lead to fire.
The pillow ball joint holder connecting the rear wheel brake master cylinder and brake pedal is made of improper material. When exposed to water containing antifreeze agents, the aluminum material of the …
In vehicles equipped with automatic transmissions, the fastening force of the fixing screws for the shift lever and parking brake lever is insufficient, causing the screws to gradually loosen. Continued operation may …
On the front and rear wheels, improper press-fitting of spacers into aluminum speed sensor panels has caused aluminum fragments to be generated from the panels. These fragments may fall into the ABS …
The retention bracket structure for the transmission shift cable routing is improper, causing misalignment of the clamp installation angle. This results in localized cable bending in some vehicles. Continued use in this …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.