Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
10624 recalls on record · page 354 of 355
In dual-axle rear-wheel vehicles, some hollow-type rear axles were assembled with cleaning solution inadvertently left inside after the machining and cleaning process. If operation continues in this condition, the cleaning solution will …
Certain idle stabilization valves (idle correction control valves) in the engine have defective return springs, which may cause malfunction of the valve and result in unstable idle speed under no-load conditions.
Retaining clips (fixtures securing the fuel hose) at the connection between the fuel distributor (device distributing fuel to fuel injection nozzles) and rubber fuel hoses (supply and return lines) have been excessively …
The electrical wiring for the engine cooling electric fan is routed improperly, causing interference with the fan motor housing edges and side member edges. Continued use in this condition may damage the …
The rubber guide piece connecting the accelerator cable to the engine throttle valve lever is made of inappropriate material. If use continues in this condition, the rubber guide piece may degrade and …
Improper welds are present at the attachment points of the body floor panel and engine room rear partition steel panels to the rear mounting section of the front suspension lower arm. If …
The plastic retainer holding the slack-lock clip in the three-point seat belt buckle of the front seats may deteriorate due to material defects when exposed to sunlight for extended periods, causing the …
The starter motor relay has insufficient water resistance. Continued use in this condition may allow moisture to enter the relay, causing an electrical short circuit that could prevent engine start.
The fuel inlet control valve (which maintains a constant fuel level in the carburetor's fuel chamber) has an improper design, potentially preventing proper regulation of fuel flow from the fuel tank. In …
During front axle manufacturing, hairline cracks developed internally in some steel material, resulting in insufficient strength in affected units. Continued use in this condition may cause cracking on the lower end surface …
In power steering systems for dual-axle front-wheel vehicles, the auxiliary boost device (sub-booster) hydraulic hose—which reduces steering effort on the steered axle (second axle from front)—has been installed in an excessively bent …
Rubber fuel hoses (supply and return lines) in the engine compartment are subject to material defects. Continued use in this condition may result in cracking of the hoses, which in the worst …
Rubber fuel hoses (supply and return lines) in the engine compartment are defective in material. Continued use in this condition may cause cracks to develop in the hoses, which in the worst …
Some fuel tanks have insufficient strength due to defects in the bottom plate molding. Continued use in this condition may cause cracks to develop in the bottom plate due to vibration during …
During assembly, a plastic retaining clip used to attach sound-damping material to the underside of the hood may have inadvertently entered the intake manifold connecting the turbocharger intercooler and the throttle valve …
The charcoal canister in the fuel evaporative emission control system has an inadequate protective cover design at the air vent port of the water-resistant air chamber. During wet-weather driving, water splashed by …
In the transfer gearbox that transmits power to the rear wheels of four-wheel-drive vehicles, defective application of liquid sealant on the mating surface between the input and output shaft cases may cause …
Improper material used in the eccentric cam bolts installed at the lower arm attachment points of the front suspension. Continued use in this condition may result in bolt fracture in the worst …
① The resin seal integrated into the brake master cylinder (hydraulic pressure generation unit) of the braking system has insufficient heat resistance. Deformation caused by engine compartment heat may occur, and continued …
The vent port installed to release internal pressure from the automatic transmission is positioned inadequately. Under severe driving conditions such as off-road driving with heavy loads, lubricating oil may seep from this …
A capacitor, which is a component of the deceleration sensor (G-sensor) used in the braking force control device (ABS: Anti-lock Braking System) of four-wheel drive vehicles, contains manufacturing defects. Continued use in …
In diesel engine vehicles, the heat shield plug that protects the bearing supporting the rotor shaft of the turbocharger (PWS: Pressure Wave Supercharger) has insufficient strength. The heat shield plug may fracture, …
The hydraulic pipe support bracket (stay) welded to the power steering oil tank on diesel engine vehicles has insufficient strength. The stay may fracture due to engine vibration and similar stresses. If …
The vacuum (negative pressure) hose connecting the engine intake manifold and brake vacuum booster is routed directly below the air cleaner intake and is too short, causing the hose to contact and …
Manufacturing defects exist in the spring attachment shaft of the front seat three-point seat belt retractor. During retraction operation, the spring may become misaligned. If use continues in this condition, strong interference …
The waterproof baffle protecting the ignition system and related components of the engine in the lower rear of the vehicle has an improper shape. During prolonged high-speed highway driving in rainy conditions, …
The plastic impeller inside the vacuum pump (vacuum booster correction device) of the brake booster—which generates negative pressure through rotation—has material defects. The impeller and internal surface of the vacuum pump housing …
A material defect exists in the resin retaining ring for hydraulic pressure assembled in the rotary valve (hydraulic circuit switching valve) of the power steering system. At low temperatures, the affected ring …
The deceleration sensor of the retractor mechanism in the rear three-point seat belt is mounted at an improper angle. When the vehicle is tilted, the emergency locking device may activate, preventing the …
Improper installation of protective resin sheets securing electrical wiring bundled within the frame (U-shaped channel) at the front of the engine compartment has caused damage to wire insulation during assembly. Continued use …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.