Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 140 of 175
In the braking system, brake shoe heat treatment is inadequate, resulting in insufficient adhesion between the brake shoe and lining in some units. Repeated brake operation may cause the lining to separate, …
Insufficient strength in the power steering cylinder anchor section. Repeated operation at maximum steering angle can cause cracks in this area. Continued use in this condition may result in anchor fracture and …
Some forward-folding seats located adjacent to emergency exits on buses are not equipped with anti-tip brackets. Consequently, if a passenger falls backward against such a seat during hard braking, the hinge fastening …
The auxiliary steering system (device for ensuring operability when working with the driver's seat facing rearward) is prohibited for use during general road operation. Due to insufficient accidental operation prevention structure, if …
The notch groove strength in the rack that controls fuel injection quantity of the fuel injection pump is insufficient. Continued use at high RPM may cause the rack to fracture, resulting in …
Improper installation of the processor controlling turn signal and wiper signals, which is built into the steering column switch cluster, may cause intermittent signal loss, resulting in turn signals and wipers becoming …
The valve material and dimensions inside the ASR (Anti-Spin Regulator) valve, which prevents drive wheel slippage, are inappropriate. Consequently, the valve experiences age-related deterioration and deformation in high-temperature environments due to air …
The tie-rod attachment point on the steering knuckle has insufficient strength. Repeated lock-to-lock steering operations can cause cracks to develop at this attachment point. Continued use in this condition may result in …
In the parking brake system, the anti-detachment structure between the parking brake spring and parking brake wire is inadequate, causing poor tracking between the spring and wire, resulting in wire slack. The …
The auxiliary steering system (a device to ensure operability when working with the driver's seat facing rearward) is prohibited for use on public roads. Due to insufficient fail-safe mechanisms to prevent unintended …
The transmission steer pump drive unit has an inadequate structure, making it difficult to supply lubricating oil to the drive unit (drive sleeve section). Continued use may cause spline wear on the …
Due to improper programming in the engine control computer, the fuel injection shutoff function may not activate even when the steering lock mechanism is engaged. If the engine is started and the …
The washer at the side stand return spring hook pin fastening section of two-wheeled vehicles has insufficient strength. Spring tension during side stand operation may cause washer buckling, and repeated side stand …
The socket portion of the brake light and tail light bulb mounting base may be defective. Due to vibration and heat, the bulbs may loosen. Continued use in this condition may result …
The socket portion of the brake light and tail light bulb mounting board contains defective components. Vibration and heat may cause the brake light and tail light bulbs to loosen. Continued use …
The outer covering of the front wheel brake cable on motorcycles is inadequate. In areas with tight cable routing, repeated flexing during cold conditions causes cracks in the outer covering, which tightens …
Improper clearance setting between the left front wheel brake pipe and the power steering hose retaining plastic clip can result in insufficient clearance due to assembly variation. During vehicle operation, vibration may …
The knuckle arm in the steering system has insufficient strength. Frequent prolonged use involving high steering force, such as lock-to-lock steering, may cause cracks in the knuckle arm. If use continues in …
The ball joint connecting the drag link and knuckle arm in the steering apparatus has insufficient strength. Frequent and prolonged use involving high steering force, such as lock-to-lock steering, may cause cracks …
In aerial work platforms, improper installation of the exhaust pipe has caused gaps in the clamp tabs on some units. Continued use may cause the clamp bolt to fracture and the exhaust …
Some airbag control units have fine cracks in the solder joints of the circuit board. Vibrations during driving may cause these cracks to propagate, resulting in circuit discontinuity. Depending on the location …
During axle assembly, some vehicles have improper lock nut tightening on the front wheel hub outer bearing, and insufficient grease fill between the front wheel hub outer bearing and hub body. As …
Due to improper machining of the axle shaft spline, engagement between the axle shaft spline and the differential side gear may be insufficient in some units. Continued use in this condition may …
The nylon tube material of the fuel pipe is unsuitable, causing cracks to develop in the tube over time. As a result, fuel may spray from the pipe, which in the worst …
The waterproof structure and heat-resistance temperature rating of the air-conditioning harness fuse terminal are inadequately specified. When rainwater enters the air-conditioning fuse holder, the fuse terminals corrode, increasing contact resistance. Heat generated …
In the power steering mechanism, hydraulic piping routing is improper. When the steering wheel is turned to its maximum angle, the piping may interfere with the link rod. Additionally, vibration during driving …
During axle assembly, some units have improper lock nut tightening on the front wheel hub outer bearing area, and some have insufficient grease fill between the front wheel hub outer bearing area …
Insufficient removal of foreign matter during electric fuel pump manufacturing can damage wiring insulation on the internal motor, causing short circuits. This may blow the fuel pump circuit fuse or cause abnormal …
①The contact point geometry of the brake light switch is inadequate for the electrical load applied to it, which can cause oxide formation on the contact surfaces and increased contact resistance. This …
The right rod of the power steering cylinder was processed improperly, resulting in insufficient strength. Repeated steering operations can cause cracks to develop in the pin hole area of the rod. Continued …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.