Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 150 of 175
The engine control computer program is inappropriate, causing misfires during high-rpm operation (approximately 5,400 rpm), which increases unburned gas, causes the catalytic converter to overheat, and in the worst case may lead …
Some bolt holes in the front brake caliper assembly have been machined improperly. Repeated brake operation may cause these sections to fracture, resulting in insufficient braking force.
Certain rack bars within the steering gearbox have improper heat treatment, which may cause premature wear or damage to the rack gear teeth through repeated steering operations. This may result in loss …
In pneumatic parking brake systems, inadequate air escape mechanisms in the air chamber allow mud and water ingress. When vent holes become blocked and the O-ring in the piston section twists, air …
Insufficient welding of frame structural components can cause cracks at weld joints and around shock absorber mounting brackets. This may result in noise during operation and, in worst cases, separation of the …
The process for partial strengthening of bus aluminum wheels was inadequate, causing tensile stress to occur in the decorative holes of the affected wheels. As a result, wheels may be damaged by …
The process for partial strengthening of aluminum wheels for buses was inadequate, resulting in tensile stress occurring at the decorative holes of the affected wheels. As a result, wheels may be damaged …
The process for partial strengthening of bus aluminum wheels was inadequate, resulting in tensile stress being generated in the decorative holes of certain wheels. Consequently, wheels may be damaged by loads experienced …
The tie rod in the steering apparatus has minimal wall thickness. On roads where de-icing salt is applied, prolonged operation may result in corrosion that reduces tie rod wall thickness. In the …
Certain cable brackets within the equalizer linkage mechanism that transmits braking force to the front and rear wheels lack sufficient strength. Repeated forceful operation of the left brake lever can cause the …
The hydraulic hose material in the power steering oil cooler section is inappropriate. Under steering operation hydraulic pressure, cracks may develop in the hose. Continued use can lead to hose rupture, causing …
The molded shape of the plastic guide portion of the shift lock release link in automatic transmission vehicles is improper, causing the link to catch on the guide and fail to return, …
The thrust washer material in the belt auto-tensioner, which maintains tension in the engine accessory drive belt, is inappropriate. Deterioration of the thrust washer can cause the auto-tensioner to fail, resulting in …
Due to improper idle control programming in the engine control unit, after cold start, engine idling becomes unstable for several minutes, resulting in insufficient vacuum generation. This causes the brake booster to …
Due to improper routing of the rear axle brake hose, interference occurs between the hose and the underbody support member (sill) when the rear suspension moves vertically. Continued use may cause the …
The idler arm of the steering system has insufficient strength. When steering lock position is frequently operated, cracks may develop in the idler arm over extended use. Continued operation in this condition …
In the braking system, some vehicles have brake tubing routed improperly, causing interference with the battery. During vehicle operation, vibration and other factors may damage the brake tubing, leading to brake fluid …
In the engine, due to inappropriate programming of the engine control computer, misfires may occur during high-speed operation (approximately 5,400 rpm), causing unburned gases to increase and overheat the catalyst, which in …
Some vehicles have the brake booster vacuum hose installed in a twisted state. When brake operations are performed continuously, the negative pressure acting on the booster may temporarily become insufficient. As a …
In the occupant protection system, improper wiring to the airbag control module may prevent collision signals from being transmitted correctly. In the event of a side-impact collision, the side airbag on the …
In the rear wheel braking system, the brake hose material and installation direction (installation direction only for some vehicles) are inappropriate. The hose is severely bent by the expansion and contraction of …
In the running gear, during axle assembly, some front wheel hub outer bearings have insufficient grease fill. Continued use in this condition may cause bearing failure due to inadequate lubrication, potentially resulting …
In the steering mechanism, the clamp that secures the oil hose to the power steering oil cooler, which is installed adjacent to the radiator, is inadequate. Under hydraulic pressure during steering operation, …
In the power transmission system, improper welding between the torque converter and ring gear inside the 3-speed automatic transmission may cause the weld to separate due to repeated acceleration and deceleration cycles. …
The parking brake cable exhibits inadequate durability performance at low temperatures, which may cause cracks to develop on the outer surface of the cable. If operation continues in this condition, the cable …
In the brake system, the parking brake cable terminal fixing point has improper crimping. When the parking brake is actuated, the cable may disengage from the fixing point, potentially resulting in parking …
In power-operated rear-view mirrors, inadequate protective circuitry may result in the protective fuse failing to blow if a short circuit or similar fault occurs in the wiring at the mirror position adjustment …
Damaged brake pipes were installed in the left front wheel brake line piping of the brake system, which may cause brake fluid leakage from the affected pipe. In the worst case, braking …
In power-operated rear-view mirrors, due to inadequate protective circuitry, if a short circuit or similar fault occurs in the wiring at the mirror position adjustment switch, the protective fuse may not blow. …
In the braking system, insufficient brake hose strength may cause oil leakage at the hose crimped section. In the worst case, the brake fluid level and pressure warning light may illuminate, and …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.