Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 134 of 175
Electric pump-type power steering systems may have improperly manufactured electrical wiring with inadequate water resistance. Water ingress can cause wiring corrosion. Continued use may allow corrosion to progress, potentially resulting in terminal …
Power steering hoses manufactured with improper material composition have inferior pressure resistance. Repeated steering operations under high load, such as lock-to-lock turning, can cause cracks in the hose. Continued operation may result …
The air piping (nylon tubing) for the parking brake (wheel parking brake) on the rear axle is routed improperly. In severe cold conditions, snow adhering to the piping freezes into ice blocks, …
The headlight mounting bracket attached to the handlebar lacks sufficient strength. Vibration during operation may cause the bracket to fracture and the headlight to detach.
In vehicles equipped with side curtain airbags, due to improper programming in the airbag control unit, deployment signals may be momentarily delayed when the vehicle receives impact from the side requiring airbag …
The intake pipe for brake booster vacuum drawn from the engine is positioned improperly, allowing engine combustion byproducts to accumulate and deposit inside the pipe. If use continues in this condition, the …
The generator start circuit printed circuit board located behind the combination meter is improperly designed. Thermal expansion of the printed circuit board caused by increased cabin temperature and self-heating of the meter …
In fire trucks, the flywheel housing bore position for mounting the engine power steering pump is improperly positioned, resulting in some units having zero backlash between the power steering pump gear and …
In the primary braking system, the resin component material in the four-circuit protection valve—a fail-safe function—is inadequate, causing the valve to deform under pressure and heat. Continued use in this condition may …
In fire trucks, the flywheel housing bore position for the engine power steering pump is improperly positioned, resulting in some units having no backlash between the power steering pump gear and the …
In large trucks, the clamp securing the fuel hose between the engine and fuel filter has insufficient strength. Engine vibration and similar factors can cause the clamp to deform, crack, or break. …
In large trucks, improper assembly of the fuel hose between the engine and fuel filter causes the hose to interfere with the EGR (exhaust gas recirculation) control hose due to engine vibration …
In plastic fuel tanks, the fuel pump retainer (fixture securing the fuel pump to the tank) may not be properly tightened. Continued use in this condition could result in fuel tank swelling …
The mechanical fuel injection pump for diesel engines has incorrect spring components installed in the fuel supply valve due to improper assembly instructions at the parts manufacturer, which may result in different …
On vehicles with front dual axles, the brake pipe geometry is inappropriate. When driving over a curb or step with studless tires mounted and the steering wheel turned to maximum angle, the …
On two-axle front vehicles, due to improper tire toe angle, when studless tires are mounted and the steering wheel is turned to maximum lock while crossing a step or curb, the tire …
① On front single-axle vehicles, due to improper tire cut angle, when studless tires are installed and the steering wheel is turned to its maximum extent while crossing a step or curb, …
Insufficient contact capacity in the brake light switch for electrical load causes contact welding during brake actuation, resulting in burn-through or thermal deformation. Continued use may cause the brake light to remain …
The power steering hydraulic pipe mounting method is inadequate, causing displacement due to engine vibration and similar factors. Depending on the pipe's fixed state, it may contact the brake pipe. Continued use …
The control rack notch groove in the engine fuel injection pump, which controls fuel injection quantity, has insufficient strength and may develop cracks in the notched section. If operation continues in this …
In the front brake system, a brake disc of smaller diameter was incorrectly installed. During braking, part of the brake pad may disengage from the outer circumferential surface of the brake disc, …
The ground cable connecting the cab and frame is not properly secured. Due to vehicle vibration and similar conditions, this cable may break, causing poor grounding. If operation continues in this state, …
In the steering console that secures the steering handle, the fixing method for the pivot shaft—which adjusts the steering handle angle according to driving posture—is inadequate. Consequently, the fastening bolts securing this …
Certain forward-folding seats installed adjacent to emergency exits on buses have insufficient strength in their anti-tipping brackets to withstand the excessive load generated during collision or emergency braking. As a result, the …
Due to improper assembly of the steering joint connecting the steering upper shaft and steering lower shaft, some units have shallow engagement between the joint and upper shaft. Continued use may result …
The terminal connectors of the electrical wiring for the DC-DC converter that charges the auxiliary battery are improperly crimped. Under prolonged use with increased electrical load, such as in cold weather, oxidation …
Some parking brake pedal stroke adjustment nuts are insufficiently tightened, causing the lock nut and adjustment nut to loosen. Continued use may increase parking brake pedal stroke, and in the worst case, …
Some rear door outer handles have defective riveting at the pivot point of the door open/close lever. When the door is closed, the lever may not fully return, resulting in the latch …
The structure connecting the valve and piston inside the hydraulic booster pressure-increase cylinder is inadequate. When brake pedal pressure is applied, hydraulic pressure may cause the valve and piston to separate. As …
Certain bell crank ball joint socket welds contain defects. Repeated locking operations such as full-lock maneuvers can cause cracks to initiate and propagate at these weld locations. If operation continues uncorrected, crack …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.