Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 143 of 175
Inadequate cleaning of internal metal fittings in the brake master cylinder causes corrosion in the rubber seal mounting groove at the cylinder rear end, potentially resulting in seal failure. Continued use may …
In common rail fuel injection systems, the flow damper (a component that restricts fuel flow) has insufficient strength. Repeated fuel pressure during fuel injection causes cracking at the flow damper's injection pipe …
The seating surface shape of the sliding plate attached to the suspension is inappropriate. During operation, force from the leaf spring causes the bolt securing the sliding plate to fracture. Continued use …
Due to improper solder on the circuit board within the control unit of the engine cooling electric fan motor, heat and other factors in the engine compartment may cause cracks in the …
Improper assembly of hydraulic piping for power steering in four-wheel drive vehicles may cause piping to contact and be damaged by engine vibration. This can result in power steering fluid leakage, increased …
The ball joint fastener connecting the front suspension lower arm ball joint to the knuckle arm has insufficient tightening torque in some cases. Due to vibration during driving, the fastener may loosen. …
Fuel supply piping around the timing belt cover is improperly installed, causing the piping and vapor pipe to cross in some vehicles. Vibration during driving causes these lines to rub against each …
① Due to improper engine control unit programming, the electronic throttle valve exhibits excessive amplitude at the closed position, which can cause damage to the electronic throttle motor stopper. This may result …
The hydraulic supply hose to the power steering unit is improperly secured. Due to vibration during operation, the hose may contact the vehicle body. Continued use could result in the hose rubbing …
In manual cab-tilt mechanisms of medium-duty trucks, inadequate clearance between the cab hook and surrounding components causes the cab hook to interfere with adjacent parts when the cab is lowered, resulting in …
The engine control unit program is inadequate, causing excessive amplitude of the throttle valve at its closed position, which may damage the electronic throttle motor stopper. This causes engine control to enter …
The locking structure of the bearing nut on the oscillation center pin and its fastening torque specification are inadequate. During vehicle operation, when oscillation occurs, the bearing washer for nut locking moves …
The contact durability of the intermittent operation relay built into the wiper actuator is insufficient. Repeated use in intermittent mode causes contact wear and partial detachment. Detached contact particles can lodge between …
Improper routing of the vacuum hose for the pressure regulator (fuel pressure control device) allows water droplets generated in the intake manifold during operation to enter the pressure regulator through the vacuum …
The mud-water intrusion prevention plate (dust cover) attached to the rear of the rear axle (non-drive axle) brake drum on two-rear-axle trucks has an inappropriate shape. During rainy conditions, mud and water …
The axle shaft has insufficient strength and may develop cracks due to prolonged use. Continued operation in this condition could result in axle shaft fracture, leading to loss of vehicle mobility.
③ Insufficient durability of the knuckle arm pin causes wear in some units. Continued use may result in steering wheel play, potentially compromising driving stability.
Some bolts securing the steering linkage pin lack sufficient tightening force, which may cause the bolt to loosen. If use continues in this condition, the bolt may fall out, and in the …
① Improper welding of the kingpin that supports the two-wheel/four-wheel steering mode-selector device at two upper and lower locations may cause cracks to develop at the weld joint between the pin and …
The power steering pump contains a spool valve that regulates internal pressure to prevent it from exceeding specified values. Due to tight clearances in this valve, if foreign matter (sand) contaminates the …
Front hub strength is insufficient. Repeated high-frequency cornering and other driving conditions may cause cracks to develop near the base of the hub flange. Additional factors such as maintenance condition and load …
The connector shape of the fuel hose connected to the fuel tank is inappropriate, which may cause incorrect installation of the connector to fail during operation. Continued use in this condition may …
The air box drain tube routing is improper, causing interference with the front cylinder exhaust pipe, which may melt and rupture. In the worst case, this could lead to fire.
The pillow ball joint holder connecting the rear wheel brake master cylinder and brake pedal is made of improper material. When exposed to water containing antifreeze agents, the aluminum material of the …
In vehicles equipped with automatic transmissions, the fastening force of the fixing screws for the shift lever and parking brake lever is insufficient, causing the screws to gradually loosen. Continued operation may …
On the front and rear wheels, improper press-fitting of spacers into aluminum speed sensor panels has caused aluminum fragments to be generated from the panels. These fragments may fall into the ABS …
Electrical wiring routing inside the instrument panel is improper, causing interference between the wiper linkage and the wiring during wiper operation. Continued use in this condition may damage the wiring, potentially causing …
Due to improper combination of the front axle beam and suspension bracket, high stress can develop at the edge of the suspension bracket mounting surface of the axle beam when traversing uneven …
Insufficient bolt tightening force at the front and rear attachment points of the drag arm shaft in the steering apparatus, and improper application of thread-locking compound may cause attachment bolts to loosen. …
The insertion of the steering joint shaft into the power steering unit was performed improperly, resulting in insufficient engagement between the shaft and unit in some vehicles. Continued use may cause the …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.