Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 144 of 175
The waterproofing of the cable for the rear door active power lock mechanism is insufficient, allowing water to ingress into the cable and cause corrosion. This increases the sliding resistance of the …
Improper assembly instructions for the distributor packing resulted in incorrect packings without ventilation holes being installed on some units. Continued use in this condition allows nitric acid to generate inside the distributor, …
Improper fuel injection timing settings in the fuel injection system can cause delayed fuel injection timing during high-load driving such as uphill operation, resulting in incomplete combustion. This may generate abnormal noise …
Improper routing of the engine wiring harness causes interference between the harness and the metal clamp of the alternator hydraulic pump rubber hose. This damages the harness insulation (exposing bare conductors), creating …
The muffler mounting bracket has an improper shape, causing contact with the engine fuel pipe in some vehicles. Continued use may result in pipe damage due to vehicle vibration, potentially leading to …
The left rear door latch has improper machining, which may prevent smooth operation of the child-proof lock mechanism lever (a device that prevents children from accidentally opening the rear seat door using …
In the cabin heater, improper harness connector mating can cause oxidation on connector terminals due to aging, generating heat. Continued use in this condition risks connector burnout and potential fire.
In cabin heater units, improper harness connector mating can result in oxidation on connector terminals due to age-related deterioration, causing heat generation. Continued use in this condition may lead to connector burnout …
The ball circulator (recirculator) structure within the power steering gear box is inadequate, resulting in insufficient strength against excessive steering input. Therefore, repeated steering operations while the tire is in contact with …
In the fuel system, some resin fuel pump mounting nuts on the upper part of the fuel tank have inadequate heat treatment. Repeated temperature fluctuations may cause cracks in these nuts, potentially …
The brake hydro-boost relief valve within the brake hydro-boost module has improper machining dimensions, which may cause seal damage. Continued use could result in hydraulic fluid leakage from the valve, potentially leading …
The rear axle bearing fastening structure is inadequate, resulting in inconsistent and insufficient bearing preload. Continued operation may cause bearing play to develop, and in the worst case, loss of steering control.
The piston cup groove machining in the pressure increase cylinder of the hydraulic booster, which amplifies brake pedal force, is inadequate in some units, resulting in insufficient air-tight sealing between the piston …
The driver-side airbag control unit contains impact sensors with solder defects. Cracks in the solder joint may cause the airbag warning light to illuminate. In this condition, airbag deployment may occur if …
Some connectors linking the fuel pipe and delivery pipe are assembled improperly, and lack retaining clips. Engine vibration may cause the fuel pipe to disconnect, resulting in fuel leakage, loss of fuel …
In right-hand drive vehicles, the clearance between the power steering hydraulic hose and the catalytic converter heat shield is inadequate, causing contact between the hose and shield. Heat from the catalytic converter …
① Inadequate waterproofing of the key switch allows water ingress between the main power contact and starter power contact inside the switch, causing leakage current. This can result in continuous starter motor …
Some vehicles have insufficient tightening torque on the front dual-tire wheel nuts, which may loosen during operation. Continued use in this condition may result in wheel nut detachment or hub bolt fracture, …
On vehicles equipped with spring-applied parking brakes, improper sealant application at the connection between the chamber body and wheel cylinder can allow water ingress into the chamber and wheel cylinder. Continued operation …
On dual-rear-axle vehicles, the spring-applied parking brake chamber mounting bracket on the rear tandem axle has insufficient strength. Vibration during operation can cause cracks to develop in the bracket. Continued use in …
On front two-axle vehicles, the brake pipe geometry is inappropriate. When crossing an obstacle with the steering fully turned, the pipe may contact the tire. Continued operation in this state could damage …
On two-axle front vehicles, ① the shape of the link rod is inappropriate, so when passing over a step with the steering wheel turned to its maximum angle, the rod may contact …
In compressed natural gas vehicles, the seal plug fastening torque of the high-pressure regulator supplying fuel is insufficient. Pressure fluctuations on the seal plug during engine start may cause the plug to …
On vehicles equipped with spring-applied parking brakes, some roller components at the tip of the wedge rod that expands the brake shoe have improper heat treatment. Consequently, the roller may fail prematurely, …
The seating surface of the attachment bolts securing the rear disc brake calipers is improperly machined. During repeated hard braking and similar driving conditions, these bolts may loosen. This can result in …
The battery ground cable attachment method is improper, which may prevent battery charging and result in battery discharge. This could cause the engine computer to shut down during operation, risking engine stall.
The anti-interference pad attached to the front-wheel brake line piping of the primary brake system is positioned improperly. During steering operations, the piping may contact the fender and abrade. Continued use may …
In vehicles equipped with automatic transmissions, the exhaust port of the vacuum pump motor that assists in providing negative pressure to the brake booster has insufficient water-resistant performance. As a result, water …
The pulley shape of the alternator with built-in vacuum pump is improper. During maintenance, if the alternator drive belt is adjusted with excessive tension, it may wear prematurely due to engine rotational …
The left and right fuel selector valve structure inside the saddle-type fuel tank is inadequate. During operation with fuel level at 1/4 or below, the valve may resonate from vehicle vibration, causing …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.