Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 149 of 175
Due to improper wiring of the carburetor warming device (carb warmer) used in low temperatures, a potential difference is generated between the carburetor and frame when the carb warmer operates. Consequently, if …
Due to improper dimensional specifications between the handle holder that secures the handlebar and the vehicle body's handle post, gaps exist at the handle holder seating surface. Running vibration and other factors …
The steering knuckle geometry of the steering system is improper, causing interference between the knuckle and the rubber boot of the ball joint on the lower arm, which can damage the boot. …
The steering knuckle shape of the steering apparatus is inappropriate, causing interference between the knuckle and the rubber boot of the ball joint with the lower arm. This can damage the rubber …
Insufficient tightening of the pressure hose connection on the power steering pump may cause hydraulic fluid to leak from the connection. This increases steering effort and, in worst case scenarios, leaked hydraulic …
Three-way dump truck bed frame vehicles have incorrect stopper components installed on the body cross hinge—the anti-withdrawal stopper that secures the bracket connecting the cargo bed to the hydraulic cylinder assembly. Continued …
Brake pipe mounting method is inadequate, causing potential interference between the brake pipe and steering gearbox fixed bracket due to vibration during operation. This results in corrosion of the anti-rust coating on …
The contact shape of the side marker light switch inside the combination switch is inappropriate. When the side marker lights are operated while the combination switch is held at mid-stroke during lane …
In right-hand drive vehicles, improper routing of the power steering pipe may cause it to interfere with the alternator. Electrical current from the alternator may conduct through the pipe to the steering …
The retaining clip securing the pin connecting the rear wheel brake master cylinder and brake pedal has an improper shape. During braking operation, the clip may interfere with an adjacent component (control …
The hydraulic piping attached to the power steering hydraulic pump has an inappropriate shape. Cracks may develop at the fitting joint of the piping mounting point due to engine vibration during rough …
The microprocessor within the airbag control unit is defective, which may cause the unit to transmit an erroneous signal during self-diagnosis. Consequently, the airbag may deploy when the ignition switch is operated.
Due to an improper arithmetic element (microprocessor) within the airbag control unit, the unit may transmit an erroneous signal during self-diagnosis. Consequently, the airbag may deploy when the ignition switch is operated.
Improper routing of brake and fuel lines may cause the brake line to interfere with the fuel line or ABS pre-charge pump. Vibration during operation may cause the brake line or fuel …
The bolts securing the tie-rod bracket to the hydraulic power steering gearbox are insufficiently tightened. During extreme low-speed steering operations such as parking maneuvers, these bolts may loosen. Continued use can result …
The torque rod front mounting bracket of the rear axle damper lacks sufficient strength against braking loads. Repeated loading causes cracks to develop in the bracket. Continued use may allow cracks to …
Some units have insufficient oil injection into the differential, resulting in inadequate lubrication. This can cause the differential to seize, and in the worst case, the wheels may lock during driving, rendering …
The terminal end shape of the brake hydraulic piping at the three-way fitting attachment point is improper in some units, causing the piping to disconnect from the fitting during braking operations. This …
The plate section securing the pin that connects the power steering rod and bracket to the bracket has insufficient strength. Repeated steering wheel operation may cause cracks to develop in this plate …
Some engine rotation sensors have improper resin filling inside. Due to engine heat and other factors, solder on the substrate may deform, causing circuit shorts and failure to transmit normal signals. As …
The air piping (nylon tubing) for the parking brake (wheel parking brake) is routed improperly. In severe cold, snow adhering to the piping freezes into ice, creating heavy loads on the nylon …
The fastening bolts of the tilt handle device (which adjusts the steering wheel angle) are insufficiently tightened. If used in this condition, the bolts may loosen. The loosened bolts can interfere with …
The tie rod connecting the knuckle and hydraulic steering cylinder is installed in an improper orientation. When operated at large steering angles, the tie rod and knuckle may interfere, causing tie rod …
The crankshaft pulley mounting bolts are insufficiently tightened. Continued use may cause these bolts to loosen, resulting in abnormal noise and, in the worst case, the accessory drive belt slipping off the …
The plating process for the torque sensor board in the electric power steering system is inadequate, which may result in plating defects and poor internal conductivity of the board. This may cause …
Variations in machining precision of the transfer-joint sleeve yoke on the rear propeller shaft result in insufficient sealing of the oil seal, causing oil leakage from the seal area. Continued operation in …
Stress from fuel pipe assembly acts on the check valve (one-way valve) fastening point mounted on the engine fuel pump. When fastening torque margin is insufficient, vibration during fuel pump operation may …
The leaf spring, which serves as a movable contact inside the brake light operation switch, is improperly assembled. Repeated brake application can cause this leaf spring to fracture. As a result, the …
The engine control module has insufficient electromagnetic shielding. Electromagnetic interference to the ignition system may cause misfiring and unburned gas emission. This can cause the catalyst to overheat, potentially resulting in fire.
In the brake system, some vehicles have improperly routed brake piping that interferes with the battery. Vibration during driving can cause the brake piping to rupture, leading to brake fluid leakage and …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.