Insufficient tightening of fuel hose clamps may allow fuel leakage at the clamp connection due to engine vibration and similar factors, potentially resulting in fire.
BMW BMW K 1200 GT 2000–2004
BMW BMW K 1200 LT 2000–2004
BMW BMW K 1200 RS 2000–2004
BMW BMW R 1150 GS 2000–2004
BMW BMW R 1150 GS Adventure 2000–2004
+9 more
① Some fuel hose connectors have O-rings that can become misaligned during connection/disconnection. Repeated connection/disconnection cycles may damage the O-ring, causing fuel leakage, which in worst cases could lead to fire.
BMW BMW K 1200 GT 2000–2004
BMW BMW K 1200 LT 2000–2004
BMW BMW K 1200 RS 2000–2004
BMW BMW R 1150 GS 2000–2004
BMW BMW R 1150 GS Adventure 2000–2004
+9 more
The flange securing the fuel tank to the vehicle body at the rear lacks sufficient strength. Repeated driving on rough roads (uneven or unpaved surfaces) causes excessive stress at the flange root, …
Honda Acty 1999–2000
The bracket position of the frame fixing the steering gearbox is misaligned, causing positional deviation between the steering gearbox and intermediate gear coupling. If continued in this condition, the coupling fastener will …
Isuzu MU 1998–2002
Isuzu WIZARD 1998–2002
The rear hub flange root has insufficient wall thickness and inadequate strength. Repeated high-frequency cornering operation may cause cracking at this location. When combined with additional factors such as machining defects near …
Mitsubishi Fuso 1989–1992
The bearing material of the fuel injection pump speed control lever shaft and the clearance between the shaft and bearing are inadequate. Repeated accelerator operation causes the shaft and bearing to seize, …
Komatsu WA40-3 2003–2004
Komatsu WA50-3 2003–2004
The bearing material of the fuel injection pump speed control lever shaft and the clearance between the shaft and bearing are inadequate. Repeated accelerator operation causes the shaft and bearing to seize, …
コべルコ LK50Z 2003
The bearing material of the fuel injection pump speed control lever shaft and the clearance between the shaft and bearing are inadequate. Repeated accelerator operation causes the shaft and bearing to seize, …
Yanmar V4-5A 2003
Yanmar V5-A 2003
Improper securing method of electrical wiring (signal and power supply) causes the wiring to interfere with the swivel stopper bracket and pipe clamps due to vibration during operation, resulting in wiring damage. …
小松メック LW250-5 1996–1997
Improper installation of brake system electrical wiring allows the wiring harness clamp to contact the brake pipe due to vibration during operation. Continued use may result in brake pipe damage, brake fluid …
Nissan - 2000–2004
In the flasher unit shared by the turn signal indicator and hazard lamp, insufficient solder quantity is present at the relay terminal solder joint inside the unit. Repeated use involving prolonged hazard …
Mazda Titan 1999–2002
Mazda Bongo 1999–2002
Mazda Bongo Brawny 1999–2002
The power steering hydraulic hose in the steering system has insufficient heat shielding. Repeated high-speed continuous driving and hill climbing in high-temperature conditions can cause the hose to degrade thermally due to …
Mazda Titan 1999–2002
Mazda Bongo 1999–2002
Mazda Bongo Brawny 1999–2002
Mitsubishi Delica 1999–2002
Nissan Vanette 1999–2002
The side-impact sensors in the airbag system have insufficient electromagnetic immunity. External electromagnetic interference may cause these sensors to transmit erroneous signals to the airbag control unit, potentially resulting in unintended deployment …
Jaguar X-TYPE 2.0 V6 2001–2002
Jaguar X-TYPE 2.5 V6 2001–2002
Jaguar X-TYPE 3.0 V6 SE 2001–2002
The interior finish of the passenger-side airbag door opening in the dashboard is inadequate, and burrs may form at the opening. If the passenger-side airbag deploys, the airbag may tear, reducing occupant …
Jaguar XJ8 3.5 2004
Jaguar XJ8 4.2 2004
Jaguar XJR 2004
Some replacement exhaust pipes were manufactured using tubing thinner than the standard thickness, resulting in insufficient strength. Continued use of such pipes may cause damage to the exhaust pipe and increased noise. …
Isuzu Elf 1993–2002
Nissan Atlas 1993–2002
The fitting shape at the accelerator cable end and the cover material are inadequate, causing the cover to degrade over time and adhere to the inner cable. This can cause the inner …
Honda Horizon 1991–1996
Isuzu Bighorn 1991–1996
Subaru Bighorn 1991–1996
In the rear axle power transmission system of four-wheel drive vehicles, some rear axle shafts have improper machining dimensions, and some have insufficient tightening of the lock nut that secures the rear …
Mitsubishi eK SPORT 2001–2004
Mitsubishi eK WAGON 2001–2004
Mitsubishi Toppo BJ 2001–2004
Mitsubishi Minica 2001–2004
Insufficient water protection on battery allows rainwater to contact the battery top surface. When the battery is replaced, depending on the filler cap design, rainwater may enter the battery interior, increasing electrolyte …
Mazda Premacy 1996–2004
ニホンフォード Isuzu Axiom 1996–2004
The engine is equipped with an auto-tensioner component that maintains timing belt tension. Some units have insufficient vibration absorption performance. Continued use may cause the external spring of the auto-tensioner to fracture, …
Mazda Capella 1996–2004
Mazda Capella Wagon 1996–2004
Mazda Familia 1996–2004
Mazda Premacy 1996–2004
ニホンフォード Isuzu Axiom 1996–2004
+4 more
The gap between the child protector lever (a device that prevents children from accidentally opening the rear door) attached to the rear door and the body panel is narrow. When the door …
Toyota Kluger V 2000–2004
Due to improper press molding of the fuel tank, some units exhibit waviness on the steel surface. This waviness can resonate with engine vibration and similar disturbances. Continued use may cause cracks …
Honda Silver Wing 2002–2003
In the running gear, improper welding between the axle reinforcement plate and the air piping pad may cause cracks at the weld. If use continues in this condition, the axle may bend …
アロー - 1993–2000
アンチコ - 1993–2000
In the rear axle attachment section with a swinging mechanism, the mounting position of the swing stopper is inappropriate. Continued use on severely uneven road surfaces causes excessive load on the mounting …
Mitsubishi FC25C 2003
In the rear axle attachment section with an oscillating mechanism, the oscillating stopper mounting position is inappropriate. Continued use on severely uneven road surfaces causes excessive load on the mounting plate that …
Mitsubishi F37 2003
The high-pressure hydraulic hose for the power steering system is installed improperly, and may be damaged by engine vibration. This could result in power steering fluid leakage and increased steering effort.
Ford Focus ST170 2002–2003
The attachment bolts on the spool valve side of the steering rack are insufficiently tightened. Repeated steering operations and vibration during driving may cause these bolts to loosen. In the worst case, …
マセラテイ Maserati Coupe GT 2001–2003
マセラテイ Maserati Spider 2001–2003
The rubber hose material of the fuel delivery hose is inadequate, which may cause fuel to leak from the joint between the rubber hose section and metal pipe section, potentially resulting in …
マセラテイ Maserati Coupe GT 2001–2003
マセラテイ Maserati Spider 2001–2003
In right-hand drive vehicles, an incorrect component is installed in the brake pipe adapter connecting the brake master cylinder and brake pipe. Vibration during driving may cause the brake pipe and power …
Alfa Romeo Alfa Romeo 156 2.0 JTS 2003
Alfa Romeo Alfa Romeo 156 2.0 JTS Sportwagon 2003
The electrical circuit from the alternator to the carburetor heater (which warms the carburetor in low ambient temperatures) is inadequately designed. When the carburetor heater operates, excessive voltage is applied to it. …
Suzuki BB-CA1PA 2002–2004
Suzuki BB-CA1PC 2002–2004
Due to improper assembly of the fuel delivery pipe to the injector, the injector seal ring may become pinched on the pipe. Continued operation in this condition could cause cracks in the …
Mazda AZ Wagon 2003–2004
Suzuki Wagon R 2003–2004