Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5188 matching recalls · page 145 of 173
In the steering system, improper machining of the power steering hydraulic pump pulley results in reduced clamping force of the pulley mounting nut. If operation continues in this condition, the pulley mounting …
Improper mounting position of oil cooler piping causes interference with starter motor wiring. Running vibrations may damage the wiring, causing short circuit and potential fire hazard in worst cases.
Variation in installation of the interior air conditioner water droplet deflection filter can result in reduced clearance between the filter and register. Additionally, filter clogging during use causes increased filter deformation under …
The passenger-side airbag inflator was subjected to an airtightness inspection using incorrect reference values, resulting in some units with insufficient airtightness. When the airbag deploys, insufficient gas pressure within the inflator may …
In the rear axle power transmission system of four-wheel drive vehicles, some rear axle shafts have improper machining dimensions. Due to repeated acceleration and turning, the lock nut may loosen. In the …
In the braking system, inadequate clearance between the brake pipe and leaf spring causes the brake pipe to contact the leaf spring, resulting in surface scratches and loss of surface plating. In …
Some transfer companion flange fastening nuts lack proper staking, which may cause the nut to loosen during operation. In worst case, the nut may detach and the propeller shaft may drop out.
Insufficient tightening of fuel hose clamps may cause fuel leakage at the clamp location due to engine vibration and other factors, potentially resulting in fire.
① The O-ring on the fuel hose connector may shift during connection/disconnection. Repeated connector operations can damage the O-ring, leading to fuel leakage and potential fire hazard.
The connector structure joining the fuel hose and pipe is inadequate. The release ring may be inadvertently pressed during maintenance, causing the connector to separate. Additionally, when reconnected during servicing, the fuel …
The oil seal mounting portion of the power steering oil pump drive shaft (which separates engine oil from power steering oil) has improperly machined anti-extrusion grooves, causing the oil seal to extrude …
The surface treatment inside the cam (variable oil compression cylinder) of the power steering oil pump is inadequate. Friction from operation causes the sliding surface temperature to rise, which can deform the …
Some front lower arm ball joint boots have improper shape, resulting in insufficient sealing of the ball joint. Additionally, due to insufficient heat resistance of the ball joint boot, the boot may …
Improper routing of the front-wheel brake line in the primary brake system allows snow accumulation and ice formation on the line during winter conditions. Ice buildup grows and hangs down, contacting the …
Electrical wiring for lighting fixtures and related components may be improperly secured, causing contact with the exhaust pipe, resulting in insulation damage and short circuits. This can cause lighting fixtures to fail …
Rear suspension lower arm reinforcement welds are improperly executed on some units, resulting in insufficient strength. When excessive input loads are applied, the lower arm may deform, potentially compromising driving stability.
②Some battery cables lack fuses installed. Vibration during operation may cause short circuits or other faults in the power circuit, causing the wiring to overheat and potentially leading to fire in worst-case …
The clearance between the battery cable and the air conditioning refrigerant pipe is narrow. Continued operation in this state may result in interference. Vibration during driving can damage the battery cable insulation, …
On vehicles equipped with gasoline engines with automatic transmissions, the brake booster (master back) has insufficient capacity. When engine idle speed increases during automatic warm-up operation, braking force may be insufficient against …
The paint application on the chassis mounting surface for the rear axle is improper, resulting in excessive paint film thickness in some cases. Vibration from the road surface may cause the rear …
The electrical wiring (main harness) routing is improper, causing interference with the return spring of the foot-operated parking brake pedal. Vibration during driving may damage the wiring, resulting in malfunction of the …
Due to improper assembly of the brake light switch, the switch mounting section is damaged and the rod that actuates the internal contact is misaligned in some units. Continued use in this …
The locking structure of the bearing nut on the oscillation center pin and its tightening torque specification are inadequate. During vehicle operation, if oscillation occurs, the bearing washer for locking the bearing …
Some wheel attachment bolts produced with incorrect material lack sufficient strength. As a result, these bolts may fracture due to tightening force during wheel installation or impact from road surface during driving.
Due to inadequate processing of the cylinder block in the propulsion hydraulic motor, partial wear of the cylinder block (9 bore holes) reduces motor volumetric efficiency, causing gradual loss of driving force. …
The strut plate that retains the front wheel coil spring has insufficient strength. In high-temperature, high-humidity environments with repeated stop-and-go traffic, cracks may develop in the plate, causing abnormal noise. If use …
Improper crimping of hydraulic hoses connecting the hydraulic control unit of the hydraulic damper system to the cross-block (circuit distributing oil to front and rear wheels) may cause internal steel wire breakage …
The contact geometry in the blower fan motor fuse circuit, which controls air conditioning airflow and similar functions in the passenger compartment, is inadequate. Continuous operation of the air conditioning at maximum …
At high altitudes with low atmospheric pressure, during high-engine-speed driving, the impeller rotation speed within the fuel pump exceeds design limits, causing excessive fuel agitation. This generates air bubbles in the fuel, …
The ABS (Anti-lock Braking System) ground wire terminal has inadequate waterproofing. Rainwater can seep through the terminal into the ground wire, infiltrating the ABS module connector. This causes electrode corrosion and short-circuiting …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.